Archive for the ‘Hobby’ Category


Pneumatic Tire- 10in.jpg

This Pneumatic Tire- 10in model was drawn in native Solidworks 2009 format. Click below to download the 3D Solidworks Pneumatic Tire- 10in model. This 3d model has been provided in multiple file formats.

Here are the actual tires, Pneumatic Tires 10″

Solidworks: Pneumatic Tire- 10in.sldprt

STEP: Pneumatic Tire- 10in.step

IGES: Pneumatic Tire- 10in.igs

Stereo Lithography: Pneumatic Tire- 10in.stl

Wood Mixing Stick- 6in.jpg

This Wood Mixing Stick- 6in model was drawn in native Solidworks 2009 format. Click below to download the 3D Solidworks Wood Mixing Stick- 6in model. This 3d model has been provided in multiple file formats.

This wood mixing stick is 6″ long, 11/16″ wide, and 1/16″ thick. This is a standard wood mixing stick. Keep in mind that these dimensions are nominal and the actual wooden stick will probably not have exactly the same curve at the ends because they appear to be hand ground and are all slightly different. The length and width and thickness appear to be consistent.

Solidworks: Wood Mixing Stick- 6in.sldprt

STEP: Wood Mixing Stick- 6in.step

IGES: Wood Mixing Stick- 6in.igs

HS-311 Hitec Standard Servo and Horn.jpg

This HS-311 Hitec Standard Servo and Horn model was drawn in native Solidworks 2009 format. Click below to download the 3D Solidworks HS-311 Hitec Standard Servo and Horn model. This 3d model has been provided in multiple file formats.

On this model, the hole spacing is standard for all standard-size servos. The HS-311 Hitec Standard Servo and Horn is a Solidworks 2009 assembly model and the servo horn is easily able rotate in Solidworks. The servo is controlled through a 3-pin connector, 2 pins are for power and the last pin is for a frequency pulse which controls the angle of rotation. Standard Servo, HS-311: Universal These servos are also easily modified to do full 360 degree rotations instead of +/- 45 degrees. This is a standard-size hobby servo found in hobby toys such as RC-Cars, RC-Planes, RC-Boats, RC-Helicopters, and even small hobby robots.

Solidworks: HS-311 Hitec Standard Servo and Horn.sldasm

STEP: HS-311 Hitec Standard Servo and Horn.step

IGES: HS-311 Hitec Standard Servo and Horn.igs


This CO2 12g Gas Cillinder model was drawn in native Solidworks format. Click below to download the 3D Solidworks CO2 12g Gas Cillinder model. This 3d model has been provided in multiple file formats.

Solidworks: co2-12g-gas-cillinder.sldprt

Iges: co2-12g-gas-cillinder.igs

Sat: co2-12g-gas-cillinder.sat

Step: co2-12g-gas-cillinder.step

Stereo Lithography: co2-12g-gas-cillinder.stl

Pro Engineer: co2_12g_gas_cillinder.prt.1

This AA Battery model was drawn in native Solidworks format. Click below to download the 3D Solidworks AA Battery model. This 3d model has been provided in multiple file formats.

This 3D AA battery model was modeled from a AA X1 1.2v Ni-MH 2400 mAh rechargeable battery, which was purchased at Fry’s Electronics. It is important to recognize that non-rechargeable alkaline AA batteries are different from Ni-MH rechargeable batteries. Ni-MH batteries are 1.2 volts and alkaline batteries are 1.5 volts. Also, AA rechargeable Ni-MH batteries are slightly larger than AA non-rechargeable alkaline batteries, so Ni-MH typically do not fit as well into electronic devices.

Solidworks: aa-rechargeable-Ni-MH-battery.sldprt

Iges: aa-rechargeable-Ni-MH-battery.igs

Sat: aa-rechargeable-Ni-MH-battery.sat

Step: aa-rechargeable-Ni-MH-battery.step

Stereo Lithography: aa-rechargeable-Ni-MH-battery.stl

Pro Engineer:aa-rechargeable-Ni-MH-battery.prt.1

This Craft Stick model was drawn in native Solidworks format. Click below to download the 3D Solidworks Craft Stick model. This 3d model has been provided in multiple file formats.

As far as I know there is only one standard size for a craft stick. Here is a 3d model of a craft stick, but most craft sticks tend to be far from perfect.

Solidworks: craft-stick.sldprt

Iges: craft-stick.igs

Sat: craft-stick.sat

Step: craft-stick.step

Stereo Lithography: craft-stick.stl

Pro Engineer: craft_stick.prt.1

This Standard 40pin Micro Processor Chip model was drawn in native Solidworks format. Click below to download the 3D Solidworks Standard 40pin Micro Processor Chip model. This 3d model has been provided in multiple file formats.

This Standard 40pin Micro Processor Chip model is a standard size for 40 pin chips. This chip size fits perfect into breadboards.

Solidworks: standard-40pin-micro-processor-chip.sldprt

Iges: standard-40pin-micro-processor-chip.igs

Sat: standard-40pin-micro-processor-chip.sat

Step: standard-40pin-micro-processor-chip.step

Stereo Lithography: standard-40pin-micro-processor-chip.stl

Pro Engineer: standard_40pin_micro_processor_prt.1

Links